2017-05-15 11:03:20

Aluminum Casting Processes

Aluminum is one of the few metals that can be cast by all of the processes used in casting metals. These processes, in decreasing order of amount of aluminum casting, are: die casting, permanent mold casting, sand casting (green sand and dry sand), plaster casting, investment casting, and continuous casting. Other processes such as lost foam, squeeze casting, and hot isostatic pressing are also mentioned.

There are many factors that affect selection of a casting process for producing a specific aluminum alloy part. The most important factors for all casting processes are:

 * Feasibility and cost factors
 * Quality factors.

In terms of feasibility, many aluminum alloy castings can be produced by any of the available methods. For a considerable number of castings, however, dimensions or design features automatically determine the best casting method. Because metal molds weigh from 10 to 100 times as much as the castings they are used in producing, most very large cast products are made as sand castings rather than as die or permanent mold castings. Small castings usually are made with metal molds to ensure dimensional accuracy.

Quality factors are also important in the selection of a casting process. When applied to castings, the term quality refers to both degree of soundness (freedom from porosity, cracking, and surface imperfections) and levels of mechanical properties (strength and ductility).

However, it should be kept in mind that in die casting, although cooling rates are very high, air tends to be trapped in the casting, which gives rise to appreciable amounts of porosity at the center. Extensive research has been conducted to find ways of reducing such porosity; however, it is difficult if not impossible to eliminate completely, and die castings often are lower in strength than low-pressure or gravity-fed permanent mold castings, which are more sound in spite of slower cooling.

Die castings
Alloys of aluminum are used in Die castings more extensively than alloys of any other base metal. In the United States alone, about 2.5 billion dollars worth of aluminum alloy die castings is produced each year. The die casting process consumes almost twice as much tonnage of aluminum alloys as all other casting processes combined.

Die castings  is especially suited to production of large quantities of relatively small parts. Aluminum die castings weighing up to about 5 kg are common, but castings weighing as much as 50 kg are produced when the high tooling and casting-machine costs are justified.

Typical applications of die cast aluminum alloys include:

* Alloy 380.0 - Lawnmower housings, gear
* Alloy A380.0 - Streetlamps housings, typewriter frames, dental equipment
* Alloy 360.0 - Frying skillets, cover plates, instrument cases, parts requiring corrosion resistance.
* Alloy 413.0 - Outboard motor parts such as pistons, connecting rods, and housings
* Alloy 518.1 - Escalator parts, conveyor components, aircraft and marine hardware and lit tings.

With die casting, it is possible to maintain close tolerances and produce good surface finishes. Die castings are best designed with uniform wall thickness: minimum practical wall thickness for aluminum alloy die castings is dependent on casting size.

Die castings  are made by injection of molten metal into metal molds under substantial pressure. Rapid injection and rapid solidification under high pressure combine to produce a dense, fine-grain surface structure, which results in excellent wear and fatigue properties. Air entrapment and shrinkage, however, may result in porosity, and machine cuts should be limited to 1.0 mm to avoid exposing it.

Aluminum alloy die castings usually are not heat treated but occasionally are given dimensional and metallurgical stabilization treatments.

Die castings are not easily welded or heat treated because of entrapped gases. Special techniques and care in production are required for pressure-tight parts. The selection of an alloy with a narrow freezing range also is helpful. The use of vacuum for cavity venting is practiced in some die casting foundries for production of parts for some special applications.

Approximately 85% of aluminum alloy die castings are produced in aluminum-silicon-copper alloys (alloy 380.0 and its several modifications). This family of alloys provides a good combination of cost, strength, and corrosion resistance, together with the high fluidity and freedom from hot shortness that are required for ease of casting. Where better corrosion resistance is required, alloys lower in copper, such as 360.0 and 413.0 must be used.

Zinc die casting part
Material: Zinc or Zinc Alloy Process: pressure die casting & gravity casting Surface Treatment: plating white zinc Specification:Sling Dogs Used for Agricultural machines; lifting machines

Zinc die casting of machine part
Material: Zinc or Zinc Alloy Process: pressure die casting & gravity casting Surface Treatment:  nature Used for Agricultural machines; lifting machines; grinding machines; medical machines

Aluminium and Zinc die casting Parts
Material: Zinc or Zinc AlloyProcess:  pressure die casting & gravity     casting Surface Treatment:  sand blasted Used for Agricultural     machines; lifting machines; grinding machines

Prev : Permanent mold casting    Next: Zinc and Zinc Alloys